Adamnium T40 Long Slim On-Metal UHF RFID Tag

Long, narrow 60 x 6 x 1.3 mm FR4 on-metal UHF RFID tag for tools, rails and slim industrial assets. Current reference range is up to 4 m on metal; validate the installed system.

Request a Quote

Category: SKU: 1349121

TECHNICAL DOWNLOADS

WHY ADAMNIUM T40

A long, narrow on-metal RFID tag for tools and slim industrial assets

Adamnium T40 is a long slim on-metal RFID tag for metal assets that provide length but very little mounting width. Its 60 x 6 x 1.3 mm FR4 body fits long tools, rails, narrow fixtures and work-in-process assets.

The current product record lists adhesive, epoxy, screw and rivet mounting. Confirm the exact production form and mounting method against the asset before release.

60 x 6 x 1.3 mmLong, slim FR4 form factor
Up to 4 mCurrent on-metal reference
NXP UCODE 8Current product record
Embedded-chip PCBFlat surface helps reduce direct impact on the IC
ADAMNIUM T-SERIES CONSTRUCTION

An embedded IC keeps the PCB surface flat

Adamnium T40 uses Crepak’s T-series embedded-chip PCB construction. The IC is embedded within the PCB, creating a flat tag surface that helps protect the chip from direct impact and collision damage during handling, installation and everyday use.

ON-METAL READ PERFORMANCE

Longer reference range in a 6 mm-wide form factor

The current product record lists up to 4 m on metal and up to 3 m on non-metal. These figures are comparison references, not guaranteed installed distances.

Reader output, antenna gain and polarization, tag orientation, asset geometry, mounting material, surrounding metal and the RF environment all affect the result. Validate representative samples on the final asset.

On-metal referenceUp to 4 m
Non-metal referenceUp to 3 m
Frequency902–928 MHz
Primary positioningLong, narrow metal assets
TECHNICAL SPECIFICATIONS

Adamnium T40 specifications

Mechanical
MaterialFR4
Dimensions60 x 6 x 1.3 mm
Weight2 g
MountingAdhesive / epoxy / screw / rivet; confirm production form
ConstructionIC embedded within the PCB; flat surface helps protect the chip from direct impact and collision damage
RF
Frequency902–928 MHz
ProtocolISO 18000-6C
ChipNXP UCODE 8
EPC memoryLegacy records conflict between 96 and 128 bits; confirm before order
Read rangeUp to 4 m on metal; application-dependent
Deployment boundary
Primary directoryOn-Metal RFID Tags
EnvironmentConfirm temperature, moisture, chemical and UV exposure
Mechanical dutyConfirm impact, vibration and fastener loads
Production releaseConfirm regional frequency, EPC configuration and mounting

Mechanical and RF values are based on the current Crepak product record. The EPC-memory field conflicts across legacy records, so the quotation and current production specification must control the final configuration. No ingress, certification or lifecycle claim is made on this page without current supporting documentation.

MOUNTING & INSTALLATION

Select mounting around the asset and process

Adamnium T40 is positioned for bonded or mechanically retained installation on long, narrow assets. The best method depends on surface preparation, available edge clearance, production process and mechanical load.

  • Verify that screw or rivet holes and clearances match the production version.
  • Keep orientation and stand-off materials consistent during installation.
  • Do not let fastener or bonding loads damage the FR4 body.
  • Re-test RF performance after the final installation method is applied.
BEST FIT / NOT SUITABLE

Choose T40 when a 6 mm width is required and T20 does not provide enough reference range

T40 is best suited to indoor metal assets with a long, narrow mounting zone. It is not the preferred choice for persistent moisture, severe outdoor exposure, sustained high temperature or heavy impact unless the complete installation is separately validated.

BEST-FIT APPLICATIONS

Industrial applications for Adamnium T40

Long Tool Tracking
Rails & Narrow Fixtures
Work-in-Process Assets
Metal Racks & Shelves
Indoor Equipment Identification
Application validation
APPLICATION VALIDATION

Validate Adamnium T40 on the real asset before volume deployment

Evaluate representative samples with the intended metal asset, mounting process, reader, antenna and operating environment. Include normal and worst-case tag orientations, then document the accepted read zone before production release.

The product-page RFQ below collects the core application inputs required for engineering review, sample planning and commercial quotation.

Selection questions
COMMON SELECTION QUESTIONS

Adamnium T40 selection FAQ

Is the 4 m read range guaranteed?

No. Up to 4 m is the current on-metal selection reference. The installed distance depends on the reader, antenna, orientation, asset geometry, mounting and RF environment.

Can T40 be used on non-metal?

The current record lists up to 3 m on non-metal, but T40 is primarily positioned as an on-metal tag. Test the actual substrate.

Which EPC memory is supplied?

Legacy records conflict between 96 and 128 bits. Crepak should confirm the current chip and EPC configuration in the quotation before production.

When should we choose a wider tag?

Choose a wider on-metal model when the asset provides more mounting area and the project prioritizes a longer read zone or stronger mechanical retention.

PRODUCT ENQUIRY

Enquire about Adamnium T40



    Optional technical details





    ALTERNATIVE RFID TAGS

    Other Options for This Application

    Compare alternative sizes, constructions or mounting options for the same application.

    Adamnium T40 Long Slim On-Metal UHF RFID Tag
    This website uses cookies to improve your experience. By using this website you agree to our Data Protection Policy.
    Read more