Adamnium T10 Compact On-Metal UHF RFID Tag

Compact 15 x 6 x 1.2 mm FR4 UHF RFID tag for small metal tools and narrow assets. The current product record lists up to 1 m on metal; actual read performance is application-dependent.

Request a Quote

TECHNICAL DOWNLOADS

WHY ADAMNIUM T10

A compact on-metal RFID tag for small tools and narrow assets

Adamnium T10 is a compact UHF RFID tag for metal assets where the available mounting footprint is very limited. Its 15 x 6 x 1.2 mm FR4 body is suited to small tools, fixtures and narrow work-in-process assets.

The current product record lists adhesive, epoxy and heat-shrink mounting, allowing the installation method to be selected around the asset geometry and production process.

15 x 6 x 1.2 mmIndustrial on-metal form factor
Up to 1 mCurrent reference read range
NXP UCODE 8Current product record
Multiple mounting optionsAdhesive / epoxy / heat-shrink tube
ADAMNIUM T-SERIES CONSTRUCTION

IC embedded within the PCB

Adamnium T10 uses the T-series embedded-IC PCB construction. The chip is set within the PCB rather than projecting above the surface, creating a flat product face that helps reduce direct chip impact and collision risk during handling and installation.

APPLICATION BENEFIT

Flat surface for constrained industrial assets

The construction is intended to support low-profile installation on small tools and narrow metal assets. Final mechanical durability still depends on the mounting method, impact direction and installed environment, so representative samples should be tested.

ON-METAL READ PERFORMANCE

Use the published range as a comparison point, then test the application

The current product record lists a reference read range of up to 1 m on metal and up to 0.5 m on non-metal. These are selection references, not guaranteed deployment distances.

Actual performance depends on the asset material and geometry, tag orientation, mounting material, reader power, antenna configuration, surrounding metal and the RF environment. Validate representative samples before volume deployment.

On-metal referenceUp to 1 m
Secondary substrate / interfaceUp to 0.5 m on non-metal
Frequency902-928 MHz
Primary positioningMetal asset identification
TECHNICAL SPECIFICATIONS

Adamnium T10 specifications

Mechanical
MaterialFR4
Dimensions15 x 6 x 1.2 mm
Weight0.24 g
MountingAdhesive / epoxy / heat-shrink tube
ConstructionIC embedded within the PCB; flat surface helps reduce direct chip impact risk
RF
Frequency902-928 MHz
ProtocolISO 18000-6C
ChipNXP UCODE 8
Memory128-bit EPC
Read rangeUp to 1 m; application-dependent
Deployment boundary
Primary directoryOn-Metal RFID Tags
EnvironmentConfirm temperature, moisture, chemical and UV exposure for the project
Mechanical dutyConfirm impact and vibration acceptance criteria
Production releaseConfirm regional frequency, encoding and mounting in the quotation

Mechanical and RF values above are based on the current Crepak product record. The current page does not include a controlled downloadable datasheet for this SKU. Request the current production specification when temperature, ingress, compliance, memory configuration or formal test evidence is part of the acceptance criteria.

MOUNTING & INSTALLATION

Select mounting around the asset and process

Adamnium T10 supports Adhesive / epoxy / heat-shrink tube. The best method depends on asset surface, production process, mechanical load and operating environment.

  • Test surface preparation and mounting consistency on representative assets.
  • Keep the tag orientation consistent through installation.
  • Confirm fastener or bonding loads do not damage the tag.
  • Re-test RF performance after the final mounting method is applied.
BEST-FIT POSITIONING

Choose T10 when minimum footprint matters more than maximum read distance.

For a longer read distance or a larger available footprint, compare T20, T40 and other models in the On-Metal RFID Tags directory.

BEST-FIT APPLICATIONS

Industrial applications for Adamnium T10

Small Tool Tracking
Fixtures & Gauges
Work-in-Process Assets
Narrow Metal Components
Indoor Asset Identification
Application validation
APPLICATION VALIDATION

Validate Adamnium T10 on the real asset before volume deployment

Evaluate representative samples with the intended asset, mounting process, reader and operating environment. Include both normal and worst-case read orientations.

Asset material and geometry
Available mounting footprint
Mounting method and surface preparation
Required read distance and orientation
Reader and antenna configuration
Frequency region and environmental exposure
Selection questions
COMMON SELECTION QUESTIONS

Adamnium T10 selection FAQ

Is the 1 m read range guaranteed?

No. It is the maximum currently listed for on-metal use. Reader power, antenna, asset geometry, orientation and nearby metal determine the installed result.

Can T10 be mounted with heat shrink?

Heat-shrink tube is listed as a mounting option. Validate that the installation pressure, material and process do not damage the tag or detune its RF performance.

When should we choose a larger tag?

Choose a larger on-metal model when the asset provides more mounting area and the project requires more read distance or stronger mechanical retention.

What should be included in an RFQ?

Provide the asset material and dimensions, mounting area, required read distance, reader setup, frequency region, environmental exposure and expected quantity.

PRODUCT ENQUIRY

Enquire about Adamnium T10



    Optional technical details





    Adamnium T10 Compact On-Metal UHF RFID Tag
    This website uses cookies to improve your experience. By using this website you agree to our Data Protection Policy.
    Read more